You are here: Home page » news » Vehicle knowledge » Dongfeng EQ2102 Series Vietnam Motor User Manual - Operation Method for Starting and Drive

Dongfeng EQ2102 Series Vietnam Motor User Manual - Operation Method for Starting and Drive

Views: 3     Author: Site Editor     Publish Time: 2021-08-05      Origin: Site

Separator operation method

There are three gears on the mandatory switch. Typically, the mandatory switch should be in the location of \\\"high \\\", when a large traction is required, the installer can decrease.

When mandatory is hangs high-end, you must pay attention to:

  1. The conversion should be carried out at the parking parking and mandatory transitions during the driver.

  2. After the clutch is stepped on, the rotator switch handle rotates to \\\"low \\\" position.

  3. Before the low grade, the front bridge drive must be engaged, in the middle, the rear axle component overload, if the front bridge is not accepted, the low frame gear does not hang.

25

1, mandatory in a lower gear

2, mandatory in idle

3, mandatory is at a high level


Forward surgery method

The striker is used to control a winch, which can be used for help or self-help. There are three gears on the stroke switch, \\\"\\\" is a winch, \\"counter \\\" is a clumsy, there is no striker, it should make the switch to \\\"empty \\\".

Using the striker, Gearbox should be in the neutral position, and press the clutch when the engine is operated, then operating the power switch.

02506873

1. Practice output, winch drum, rent steel wire

2, idle

3, stroke output, winch drum relax wire rope

When the current bridge, official means or power is operated, if the feeling does not work, first check if the indicator light is lit, if it is not illuminated, the description does not hang in the working gender, or is still neutral. This is usually the following reason:

1. Because the gear position is not suitable, you can't hang it once. At this point, you can send a car forward or later.

2. Long-distance control switch is not open.

3. The air pressure is too low, the cylinder pusher is not in place, and the pipe should be expanded until the pressure rotates more than 600 kPa and then re-deposited.


Driving instruction

The correct driver method can not only extend the life of the vehicle, but also improve economic benefits, and the impact on the safety vehicle is also very much.

The following provisions should be observed when driving:

1. When the engine is colder, there should be a preheated process before the vehicle begins. After the cold machine is started, the engine speed increases, so that the oil pressure, the engine combustion has stabilized with the engine. The engine is running until the exhaust color is light blue.

2. Don't increase the engine speed too quickly. The coolant temperature is low speed to increase the engine to damage the engine. When the external temperature is less than 0 ° C, the engine can transfer for 5 minutes before full load.

The throttle must be avoided and the sudden brake is stopped. The throttle will result in clutch damage or uneven tyre wear; sudden brake accelerate tyre and the wear of the brake grinding machine.

4. Pay attention to changes in the hydraulic pressure within 15 seconds after the start.

5. After running a large amount of load in the engine, you must be idle for 3 to 5 minutes before stopping.

6. Not 4,000km before driving, the engine speed should not exceed 2,800 r / min.

7. Strictly ban use \\\"accelerate an empty gear slide \\\.

8. It is strictly forbidden to operate the vehicle overload, and the overload will shorten the service life of the vehicle.

9. The specified lubricant and diesel must be used, and the appropriate oil is selected according to the local temperature temperature.


This article reprints from the following products: Dongfeng Automotive Company - \\\"Dongfeng EQ2102 / EQ2102G Series Vietnam Motor User Manual \\\"


Hubei Off-Road Special Vehicle Co., Ltd.
Address: No. 6, Huimin Road, Maojian District, Shiyan City, Hubei Province, China
Tel: 86-719-8888190 Tel: 86-18986895008 / 86-18986890909 Email:fanya_trade@163.com
Copyright © 2021 Hubei Off-road Special Vehicle Co., Ltd. Record certificate number:Hubei ICP No. 20010516-3