You are here: Home page » news » Vehicle knowledge » Dongfeng EQ2102 Series Vietnam Motor User Manual - Structure and Operation - Traction

Dongfeng EQ2102 Series Vietnam Motor User Manual - Structure and Operation - Traction

Views: 7     Author: Site Editor     Publish Time: 2021-08-04      Origin: Site

Traction

1. Place the parking brake handle to the \\\"brake \" position and hide the wheel with a wooden block.

2. Place the clutch pedal and turn the power switch to \\"counterattack \\\" position.

3. Slowly release the clutch pedal, balance the oil, and can collect wire ropes and start to be pulled.

4. After the traction is completed, the clutch pedal is placed, so that the power stroke switch is located in the idler, the drum is in the \\"separation \\\" location.

0 ERT01.

1. Release the brake 2, the brake position 3, pull up

notes:

1. If the winch does not use a longer time longer, the lubricating oil surface of the winch gearizer should be checked before use, and add it after adding. Before use, there should be a hard object between the winch drive shaft and the frame to avoid damaging the drive shaft and the power board.

2. The wire rope should be wrapped in a winch. Typically, the wire rope should be packaged immediately until the next use. The wire rope is not tested, and the traction will enable the upper wire rope to enter the next layer, resulting in steel wire and is easily damaged.

3. The working length of the wire rope should not exceed 54 meters, and the remaining wire rope wrapped around the drum should not be less than 5 laps.

4. Prohibition of long-term continuous use of winches, such as long usage, pay attention to the temperature, no heat, such as purity of the reducer, and maintain it after cooling.

5. When the wire rope must be pulled out of manpower, otherwise, the wire rope on the roller will automatically loosen in the reverse direction, so that the upper line will enter the next layer, the card is broken. The maximum traction of the winch is 4,500kg, which is not allowed to use it. If you need a greater traction, a pulley should be used.

6. The traction direction of the wire rope should remain perpendicular to the flattening of the bumper, and the traction direction may not exceed 15 ° of the vehicle centerline to avoid transmitting and damaging the guide.


warn:

When the winch is first used, the wire rope should be discharged (54 meters), then tighten the wire rope in the case of load (4500 kg), how much it takes in the future, which can reduce the wire rope in the process of use, the wire rope will prevent the wire rope from being damaged prematurely.

2. Don't engage in winches and drag your car with a wire rope.

3. When the winch is prohibited, stand on the wire rope.

4. Disable the demolition of the automatic brake.

5. The maximum traction of the winch is 4,500kg, such as the load is too large, can cut the safety pin of the drive shaft universal joint fork to the strip to avoid damaging the winch.

6. Prohibit instead of bolts or other parts of safe sales.

1SD0.

Security Code


according to

The pulley is used to increase the traction of the winch and change the traction direction.

1. Use a pulley to change the traction direction.

2. When the angle and the traction direction of the vehicle exceed 15 °, the traction direction must be changed in the traction direction.

1P0

3. When the mutual rescue needs to increase traction, the pulley must be fixed to the preserved front traction hook.

IH10.

1, fixed pillar 2, pull tube


This article reprints from the following products: Dongfeng car - \\\"Dongfeng EQ2102 / 2102G series Vietnam Motor User Manual \\\"

Hubei Off-Road Special Vehicle Co., Ltd.
Address: No. 6, Huimin Road, Maojian District, Shiyan City, Hubei Province, China
Tel: 86-719-8888190 Tel: 86-18986895008 / 86-18986890909 Email:fanya_trade@163.com
Copyright © 2021 Hubei Off-road Special Vehicle Co., Ltd. Record certificate number:Hubei ICP No. 20010516-3