You are here: Home page » news » products information » Dongfeng off-road vehicle The adjustment and exclusion of the cab is the adjustment and exclusion of the cab - the adjustment of the cab (1)

Dongfeng off-road vehicle The adjustment and exclusion of the cab is the adjustment and exclusion of the cab - the adjustment of the cab (1)

Views: 7     Author: Site Editor     Publish Time: 2021-10-25      Origin: Site

In the third quarter, the adjustment of the cab

First, the adjustment of the door

1, adjustment of the front door

Check, adjust the door of the door, so that the whole gap is uniformly maintained within 6 to 10 mm of the specified range. Move the lock body up and down, adjust the horizontal and vertical direction and the front, and then in the inside and outside. The specified gap is as follows:


LocationAdjust data
Door lock column pin and door lock2 ~ 5mm
Door plate and side plate0 ~ 3mm
Door lock column pin and lock tongue1.5 ~ 4.5mm


2, the adjustment of the rear door

The gap between the rear door is generally within 6 to 10 mm. The adjustment method is: adjust the position of the large curved arm hinge and the middle struts and adjust the position of the large curved arm and the door to adjust the gap of the door; the coupling position of the large bend arm hinge and the middle pillar and the coupling position of the big bend arm Add or reduce the gasket to adjust the left and right positions of the door. The time for the rear car is too long, which may cause the trace of the door to slide, causing the door lock and the column pin, which can be adjusted as follows: Adjust the position of the large curved arm and the middle pillar and adjust the large curved arm and the door Location, make the door change a small angle to align the door lock with the column pin.

Second, the installation method of automobile door glass

1. Place the door glass assembly from the window hole until the middle of the car door

2. Turn the door glass assembly to the front and rear railings.

3, shake the glass lift handle, so that the front end of the slide is exposed to the opening of the fixed lifting portion of the door, and the front end of the glass lift is fixed with the screws.

4, continue to shake the handle, expose the back of the slot to the opening of the door lock portion, fix the rear of the glass clip frame, and remove the glass, in the opposite order of the above, still removed from the window hole .

Third, wiper

1, pneumatic wiper

Sometimes, after ventilating the pneumatic wiper, the wiper blade will not operate, then simply pull the wiper handle to the left and right limit, in most cases the wiper can recover the work. The main reason is that the reversal valve piston is in an intermediate position, and the seal is just blocked the two intake channels, causing the compressed air to enter the wiper, and cannot drive a large piston movement.

If the above operation does not recover the wiper operation, it may be that the surface of the wiper is dry, and the motion of the exercise is caused to take the champion on the right side of the reversing the valve body, screwed into the right end with bolts. In the threaded hole, pull out the piston, lubricate, can exclude the fault.

When the wiper has obvious leaks, the reason is damaged when the reason is damaged and needs to be replaced.

Fault formCauses and treatment
When using the front windshield scrubber, only water is not shaved

The wiper relay line beam connector is detached and should be corrected.

The combined switching wire beam connector is detached and should be corrected.

The internal contacts of the combination switch are poor contact, check the contact condition and exclude.

When using the front windshield scrubber, the nozzle does not spray the water

Deterneer water spray motor wire beams fall or combined with poor contact. Check and exclude.

Poor motor contact. Check and exclude.

Cassette is bent. Open the scrubber, if you hear the motor work is still not sprayed, the pipeline is blocked or bent.

Wiper does not work

Insurance wire break. Check whether the bull is broken and check the contact.

Wiper brush connecting rod mechanism falls off. Open the wiper and listen carefully if there is a motor work sound, if there is a sound, the link mechanism ball is offset and must be replicated. Wiper motor damage needs to be repaired or replaced.

This article is reproduced from: Dongfeng Truck Company Heavy Car Factory - \"Military Dongfeng off-road vehicle Adjustment and Maintenance Manual

Hubei Off-Road Special Vehicle Co., Ltd.
Address: No. 6, Huimin Road, Maojian District, Shiyan City, Hubei Province, China
Tel: 86-719-8888190 Tel: 86-18986895008 / 86-18986890909 Email:fanya_trade@163.com
Copyright © 2021 Hubei Off-road Special Vehicle Co., Ltd. Record certificate number:Hubei ICP No. 20010516-3