The maintenance of the hub bearing is 12,000km, and the maintenance of the wheel hub bearing is carried out. Remove the wheel and brake drum, clean the hub bearing clean, check whether the grease of the hub bearing has changed, hydration, etc., if it should be replaced in time. When the grease is changed, the gap of the bearing roller is filled with the gap of the bearing roller and coated around the bearing. Do not fill the grease in the wheel cavity to avoid causing the hub oil leakage. Adjustment of the H-A-02G hub bearing 3, the locking placement 1, the groundwashing spacer 4, the outer nut 2, the inner nut is not equipped with half shaft, and the wheel is joined. After installing the gauze, tighten the nut in 200 ~ 250N.m, then loosen 1/5 ~ 1/4 lap, install the locking washer, and finally tightened with 250n.m and torque. The adjusted wheel should be free to rotate without obvious axial loose or swinging. Note: 1. When tightening the inner nut, it should be in two
The maintenance of the balance the bearing hub checks the balance bearing hub. The balanced hub lubricating oil is replaced each by 8,000 km. After the new car is completed, the U-shaped bolt nut of the steel plate spring should be tightened in the heavy-duty state; each running 12,000 km, the steel spring U-shaped bolt nut is fastened in the heavy-duty state. Before the examination, the rear steel sheet side surface clamping bolt is loose, and if there is loose moment, it must be tightened. Based on the side plates of the balance bearing hub, the steel plate bullet is moderately eliminating the clearance. Check the balance shaft bracket and frame, and the connecting bolts of the connecting axis are non-loosening. If there is a loose and provenance torque. The balance bearing hub axis adjusts 8,000 km cleaning, check and adjust the balance bearing hub. 1. Remove the balance bearing hub, release the locking bolts on the adjustment nut, tighten the adjustment nut / 1/4 ring, then at 170 ~ 220n.m
When the direction of the steering wheel is freely rotating, when the swelling 2,000km maintenance, the amount of self-rotating of the drawing plate should be checked, and the amount of free rotation in the middle position cannot exceed 15 °. H-B-096 Plantation and Replacement Transmission Oil Quality Period Row 4,000km La Nan as the 0-speed gas refueling and oil surface inspection hole, the height of the oil surface with the row of twepight holes, not added. At the same time, it should also check the condition of ventilation and cleaning. Black heat cycle HA-0301, refueling and oil surface inspection hole 2, put oil-absorbing screw release 4,000km maintenance time to reduce the transmission of the transmission in the hot air condition In the middle of the mountain, the cleaning rush (the sputum is self-sufficiently adsorbed in the iron) of the iron), adding a new hole slip from the oil and oil surface inspection hole. I would like to burn the bearing and gear, which will cause overheating and oil leakage. Continuous ventilation
Check and replace the power steering hydraulic oil before the oil plane is checked, the oil tank is clean. Remove the fueling cover with oil rod assembly, wipe the ruler, reload the oil ruler, then take the oil standard, observe the height of the oil plane. If the oil plane is not on the bottom of the oil roll, it is necessary to add the same type of hydraulic oil inspection cycle for the first 4000km replacement cycle for the first time, 4000km per drive 24000km replacement method 1. Put the car's rear wheels with triangle pads , The transmission is set, and the front axis is jealous with jack, so that the two sides tyre are separated from the ground 2. Remove the steering and extracting the tubing, all discharge the oil fluid of the steering system. At the same time, start the engine, reverse the steering wheel 3. After confirming that the system oil discharges clean, open the storage tank cover, replace the hydraulic oil filter 4. After the filter is replaced, the oil tank is added, and the engine will start the engine. The engine is idling, after the flameout
